How to Change a Single Handle Kitchen Faucet Washer
❤️ Click here: How do you replace a kitchen faucet washer
Then, find the solutions to that area below. Reassemble valve cartridge and replace in body following instructions given in 1 above. To do this, you will need a Phillips screwdriver or an Allen wrench depending on your handle type.
Also match the stem end where the handle attaches. This convenient fixture allows you to press the handle upward at almost angle to receive hot, warm, or cold water. If you do not find the answer you need here, please use the Support Information Search to find maintenance instructions for your specific model.
How to Install a Kitchen Faucet - Remove the escutcheon cap, unscrew the disk cylinder mounting screws and lift out the cylinder. Reassemble the faucet and tighten the packing nut.
The toughest part of replacing a kitchen faucet is removing the old one. Unexpected problems always pop up—corroded pipes, difficult-to-reach nuts and poor access to fittings. Barring unforeseen problems, you could be washing up under the faucet in an hour or so. In this article walk you through a basic replacement process and tell you how to get through those tough parts. Place a bucket or coffee can under the P-trap to dump residual water after you pull it free. If the faucet still drips, install new ones. But if not, buy whichever valve type is compatible with your pipes. This weird little wrench is made specifically for removing and installing those hard-to-reach fasteners that clamp older faucet assemblies to the sink. Newer faucets have plastic Wing-Nuts that can usually be loosened and tightened by hand. If you need to remove drain lines to access the faucet, get a pipe wrench or slip-joint pliers Photo 1. For cutting copper tubes, buy a conventional tubing cutter. But if your copper supply lines are within a few inches of the back of the cabinet, buy a special mini tube cutter Photo 3. Before disconnecting the drain lines, take a snapshot or make a sketch of the layout to help you put it all back together. Photo 2: Disconnect the garbage disposer Unplug the garbage disposer, or shut off the circuit breaker in the main service panel if the disposer is directly wired. Disconnect the dishwasher discharge line and place a 1-gal. Release the disposer by tapping the retaining ring with a hammer in a counterclockwise direction. Open the kitchen faucet and another lower faucet to bleed off any pressure and to drain the water. Close-up of Photo 4 Fit the basin wrench jaws around the lock nuts. After you pull out all of the cleansers, buckets and old vases from under the sink, go ahead and lie under there and see if you can easily access the faucet. If so, go right to Photo 3. Most likely, the main obstacles will be the pipes and P-traps that drain the sinks. After you remove them, throw all the parts in a box for matching them exactly at the store later. Sometimes a garbage disposer can be a 20-lb. Unplug it and pull it out of the cabinet to get it out of the way. The first step in removing the old faucet is to disconnect the water supply lines Photo 3. Make sure new valves are closed before turning the water back on to the house. Once the water lines are disconnected, use the basin wrench to loosen the old faucet and remove it Photo 4. Try soaking the threads with penetrating oil and try again. Loosen the screws on the bottom of the sink rim for a clamp-down sink, or cut the caulk between a drop-in sink and countertop with a utility knife and lift out the sink. Photo 6: Tighten the faucet mounting nut. Then slip on the faucet washer, and thread on and tighten the faucet-mounting nut from below, gently spreading the faucet supply tubes if necessary to gain tool clearance sometimes manufacturers provide a special tool for this. Photo 8: Attach the spray hose to the faucet supply tube. Thread the spray nozzle line through the faucet body, then thread the spray hose fitting onto the faucet supply tube and tighten it. Photo 10: Connect the supply tube to the supply lines. Clean the copper tubing with fine sandpaper, then slip the nut, compression ring and valve body over the pipe and tighten. Close the valve, turn on the main water valve and check for leaks. Place a bucket under the faucet and turn the faucet on to check for leaks. Reassemble the garbage disposer, P-traps and drain lines. Some even come with a lifetime warranty.
Faucet Repair : How to Repair a Dripping Kitchen Two-Handle Faucet
At his own Second Empire house, it's more the case of the cobbler's child whose feet go unshod. He installs a new one, making sure that he places it in the same position as the one he just pulled out, so the elements in its side that deliver the hot and cold water to the spout will not be mixed up. Remove decorative parts of the faucet. To avoid damaging the faucet finish, you may want to place a jar opener gripper or heavy cloth between the cap and wrench. If you have resistance handles, pry off the handle button, remove the screw and lift off the handle. Over-tightening the adjusting ring can cause premature wear of the seal surfaces, making frequent repairs necessary. You can then pull out the handle. Use a crescent wrench to loosen if glad.
